Main Page

Introduction

Welcome to the wiki for the SoC Design course! We started this series of labs/projects in 2014 and we are upgrading and fixing problems every year to make it better.

Slides for the introductory presentation are available here

Learning Objectives

After the completion of the labs, you will be able to:

Tutorials: Make Linux kernel drivers: Write a simple kernel driver for controlling a simple IP (intellectual property) on ZedBoard. Build custom SoC (System-on-Chip) on ZedBoard: Create a simple SoC with Vivado from existing IPs Build a custom embedded Linux system to run on the SoC Using custom kernel drivers to control the IPs in the SoC Create custom IPs: Development of simple custom IP from VHDL code Integrate the IP into the SoC using AXI bus Control the IP from Linux using custom driver Build a simple audio processor system Complex system integration Preparation for course project

Project: Component reuse and system improvement Functional test and analysis Work in a team

Requirements for Taking the Labs

For these labs we assume that you have basic knowledge of the following:

• C language <- This is a must!
• Digital Systems Design
• Embedded Systems Programming

Lab Organization

Important dates Week 2: Lab 1 Week 3 ... week 5: Lab 2 Week 6 ... week 9: Lab 3 Week 10, week 11: Lab 4 End of week 15: Project Deadline

Lab Grading Policy Tutorials (Pass/Fail - prerequisite for project) Project (50% of the grade) Examination (50% of the grade) In order to pass the course, you have to get a positive result in both the project and the exam. You cannot finish the project without passing all tutorial labs!

Rules and Regulations

Please read the following page before you start the course:

Timing and Plans

Please note that the project's (strong) deadline is on the last lab session, no extension will be made!

General Rules

• Unplugging any cables from the lab computers is NOT ALLOWED! If you use your own computer, please use Wi-Fi.
• It is OK to discuss your code with colleagues during the labs.
• Copying a colleague's code is not OK! You need to write your own code.
• You must understand the code you write! We will check that you do!

Writing Code

In order for your code to be reusable, please keep these things in mind:

• Every code you write should print out your name as the first thing it does, otherwise you are not allowed defend the lab! Kernel modules should print your name when they are inserted.

(This requirement only applies for code which you write yourself or modify)

• Use comments in your code. Even you, as the programmer who wrote the code, will otherwise not understand it after a while.
• Write a proper doc-string for the functions. It makes the life of you and others much easier.
• Use meaningful variable names. The purpose of a variable with the name "counterMaxValue" is much easier to understand that the same variable with the name "cMNum", for example.

In Case of Problems

Please use the following methods in the following order for solving your issues:

1. Check the current lab's additional materials.
2. Re-read the lab manual to make sure you did not miss anything.
3. Google your problems
4. Ask the lab assistants for help.

NOTE: In case you find a problem with the documentation, please tell the assistants. Then we can fix the problem and everyone will be happy :)

Lab Results

	You can view you current lab results and statistics here

Contact Us

In case of any questions, please contact us:

	• Karl Janson
	• Madis Kerner

Labs

Lab Tutorials

Here you can find lab manuals for the tutorials:

• Lab 1: Building custom SoC on ZedBoard TBU
• Lab 2: Kernel Driver TBU
• Lab 3: Custom IP creation TBU
• Lab 4: Setup 1 board system for the lab TBU

Additional Material

Additional reading materials and more information about the labs can be found here:

Lab Specific Information

• Lab1 Additional Material
• Lab2 Additional Material
• Lab3 additional material TBU
• Lab4 additional material TBU

General Information

• Creating New Vivado Project
• Basic Linux Usage
• Using ZedBoard

Audio Mixer Project

Design project is defined in each round for System on Chip design(IAY0550) students with the aim of providing them with real world experience of working on a SoC project, teamwork and project management. This wiki will serve as a platform for students to pass-on their designs and documents to students in the next round of course. Full description of the project can be found on the Project Description page

• Project Description page.

Using Own Computer for the Labs

You can find some information about using your own computer on the Using Own Computer page.

Please note that using any other computer than the ones in lab is not officially supported. The information on this page is not checked by the lab supervisors and might not be up-to-date and might not work! We recommend not to rely your course progress on getting the systems running on your personal machine and use the lab computers!

However, if you decide to follow the instructions on the page, please let us know about the problems you encounter, so we can update the manual for the benefit of other students.

Git

The project code should be stored in git. Every component of the project should be uploaded as a separate branch.

There exists a dedicated Github repository for the course, that can be accessed here: [1]

Archive

Tutorials:

• 2016 Tutorials
• 2015 Tutorials
• 2014 Tutorials

Design project:

• Old project archive (2014/2015)